|
|
An event is a significant occurrence in the system or in an application that requires administrators to be notified. The operating system writes notifications for these events to the Linux system log. The location of the log file depends on the configuration of /etc/syslog.conf, however, by default, it is /var/log/messages. The following table identifies the events generated by Double-Take Availability.
1 This evaluation period has expired. Mirroring and replication have been stopped. To obtain a license, please contact your vendor.
Error—Contact your vendor to purchase either a single or site license.
2 The evaluation period expires in %1 day(s).
Information—Contact your vendor before the evaluation period expires to purchase either a single or site license.
3 The evaluation period has been activated and expires in %1 day(s).
Information—Contact your vendor before the evaluation period expires to purchase either a single or site license.
4 Duplicate activation codes detected on machine %1 from machine %2.
Warning—If you have an evaluation license or a site license, no action is necessary. If you have a single license, you must purchase either another single license or a site license.
5 This product edition can only be run on Windows Server or Advanced Server running the Server Appliance Kit.
Error—Verify your activation code has been entered correctly and contact technical support.
3000 Logger service was successfully started.
Information—No action required.
3001 Logger service was successfully stopped.
Information—No action required.
4000 Kernel was successfully started.
Information—No action required.
4001 Target service was successfully started.
Information—No action required.
4002 Source service was successfully started.
Information—No action required.
4003 Source service was successfully stopped.
Information—No action required.
4004 Target service was successfully stopped.
Information—No action required.
4005 Kernel was successfully stopped.
Information—No action required.
4006 Service has aborted due to the following unrecoverable error: %1
Error—Restart the Double-Take service.
4007 Auto-disconnecting from %1 (%2) for Replication Set %3, ID: %4 due to %5
Warning—The connection is auto-disconnecting because the disk-based queue on the source has been filled, the service has encountered an unknown file ID, the target server has restarted, or an error has occurred during disk queuing on the source or target (for example, Double-Take Availability cannot read from or write to the transaction log file).
4008 Auto-disconnect has succeeded for %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4009 Auto-reconnecting Replication Set %1 to %2 (%3)
Information—No action required.
4010 Auto-reconnect has succeeded connecting Replication Set %1 to %2 (%3)
Information—No action required.
4011 Auto-reconnect has failed connecting Replication Set %1 to %2 (%3)
Error—Manually reestablish the replication set to target connection.
4014 Service has started network transmission.
Information—No action required.
4015 Service has stopped network transmission.
Information—No action required.
4016 Service has established a connection to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4017 Service has disconnected from %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4018 %1, however, mirroring and replication have been disabled as a restore is required due to a previous failover.
Warning—Perform a restoration.
4019 Service has started a mirror to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4020 Service has paused a mirror to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4021 Service has resumed a mirror to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4022 Service has stopped a mirror to %1 for Replication Set %2, ID: %3, %4
Information—No action required.
4023 Service has completed a mirror to %1 %2 for Replication Set %3, ID: %4, %5
Information—No action required.
4024 Service has started Replication to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4025 Service has stopped Replication to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4026 The target has been paused due to user intervention.
Information—No action required.
4027 The target has been resumed due to user intervention.
Information—No action required.
4028 Registration of service class with Active Directory failed. Verify that the Active Directory server is up and the service has the proper permissions to update its entries.
Warning—Verify that the Active Directory server is running and that the Double-Take service has permission to update Active Directory.
4029 Registration of service instance with Active Directory failed. Verify that the Active Directory server is up and the service has the proper permissions to update its entries.
Warning—Verify that the Active Directory server is running and that the Double-Take service has permission to update Active Directory.
4030 RSResource.dll has an unknown error. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4031 RSResource.dll could not be opened. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4032 The RSResource.dll component version does not match the component version expected by the product. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4033 RSResource.dll build version is invalid. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4034 Error verifying the service name. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4035 Error verifying the product name. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4036 Error verifying the vendor name. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4037 Error verifying the vendor URL name. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4038 Error verifying the product code. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4039 Error while reading RSResource.dll. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4040 The product code is illegal for this computer hardware. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4041 The product code is illegal for this operating system version. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4042 The product code requires installing the Windows Server Appliance Kit. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4043 This product can only be run on a limited number of processors and this server exceeds the limit. The product functionality has been disabled.
Error—Reinstall the software, using the installation Repair option, to install a new copy of the RSResource.dll. Contact technical support if this error persists.
4044 An error was encountered and replication has been stopped. It is necessary to stop and restart the service to correct this error.
Error—Contact technical support if this error persists.
4045 %1 value must be between 1025 and 65535. Using default of %2.
Error—Verify that the Double-Take Availability port value you are trying to use is within the valid range. If it is not, it will automatically be reset to the default value.
4046 This service failed to start because of a possible port conflict. Win32 error: %1
Error—Verify that the Double-Take Availability ports are not conflicting with ports used by other applications.
4047 Could not load ZLIB DLL %1. Some levels of compression will not be available.
Error—The compression levels available depend on your operating system. You can reinstall the software, using the installation Repair option, to install a new copy of the DynaZip.dll, or contact technical support if this error persists.
4048 Service has started a delete orphans task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4049 Service has paused a delete orphans task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4050 Service has resumed a delete orphans task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4051 Service has stopped a delete orphans task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4052 Service has completed a delete orphans task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4053 Service has started a restore task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4054 Service has paused a restore task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4055 Service has resumed a restore task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4056 Service has stopped a restore task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4057 Service has completed a restore task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4058 Service has started a verification task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4059 Service has paused a verification task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4060 Service has resumed a verification task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4061 Service has stopped a verification task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4062 Service has completed a verification task to %1 (%2) for Replication Set %3, ID: %4
Information—No action required.
4063 Bandwidth limit to %1 (%2) has changed to %3.
Information—No action required.
4100 Product activation code is invalid. Please check that it is typed correctly and is valid for the version of the operating system in use.
Error—If you are in the process of installing Double-Take Availability, verify that you are using a 24 character alpha-numeric code. If Double-Take Availability is already installed, confirm that the code entered is correct. If the code appears to be correct, contact technical support.
4101 This service will not run on this device. Contact your sales representative for upgrade procedures.
Error—The activation code does not match the type of server you are attempting to run on. Contact your vendor for a new activation code or contact technical support.
4110 Target cannot write %1 due to target disk being full. Operation will be retried (%2 times or forever)
Warning—The disk on the target is full. The operation will be retried according to the TGExecutionRetryLimit setting.
4111 Target can not write %1 due to a sharing violation. Operation will be retried (%2 times or forever)
Warning—A sharing violation error is prohibiting Double-Take Availability from writing on the target. The operation will be retried according to the TGExecutionRetryLimit setting.
4112 Target can not write %1 due to access denied. Operation will be retried (%2 times or forever)
Warning—An access denied error is prohibiting Double-Take Availability from writing on the target. The operation will be retried according to the TGExecutionRetryLimit setting.
4113 Target can not write %1 due to an unknown reason. Operation will be retried (%2 times or forever). Please check the log files for further information on the error.
Warning—An unknown error is prohibiting Double-Take Availability from writing on the target. The operation will be retried according to the TGExecutionRetryLimit setting.
4120 Target write to %1 was completed successfully after %2 retries.
Information—No action required.
4150 Target write %1 failed after %2 retries and will be discarded. See the event log or log files for error conditions. After correcting the problem, you should re-mirror or run a verify to resynchronize the changes.
Error—The operation has been retried according to the TGExecutionRetryLimit setting but was not able to be written to the target and the operation was discarded. Correct the problem and remirror the files.
4200 In band task %1 submitted from %2 by %3 at %4
Information—No action required.
4201 In band task %1 discarded (submitted from %2 by %3 at %4)
Warning—A task may be discarded in the following scenarios: all connections to a target are manually disconnected, replication is stopped for all connections to a target, or an auto-disconnect occurs. If one of these scenarios did not cause the task to be discarded, contact technical support.
4202 Running %1 in band script: %2 (task %3 submitted from %4 by %5 at %6)
Information—No action required.
4203 Completed run of in band script: %1 (exit code %2)
Information—No action required.
4204 Error running in band script: %1
Error—Review the task and its associated script(s) for syntax errors.
4205 Timeout (%1 seconds) running in band script: %2
Warning—The timeout specified for the script to complete has expired. Normal processing will continue. You may need to manually terminate the script if it will never complete.
4206 Run timeout disabled for in band script: %1
Warning—The timeout period was set to zero (0). Double-Take Availability will not wait for the script to complete before continuing. No action is required.
4207 In band scripts disabled by server - no attempt will be made to run %1
Warning—Enable task command processing.
4300 A connection request was received on the target before the persistent target paths could be loaded.
Error—You may need to disconnect and reconnect your replication set.
4301 Unable to block target paths, the driver is unavailable.
Error—If you need to block your target paths, contact technical support.
4302 Target Path %1 has been successfully blocked
Information—No action required.
4303 Blocking of target path: %1 failed. Error Code: %2
Warning—If you need to block your target paths, contact technical support.
4304 Target Path %1 has been successfully unblocked
Information—No action required.
4305 Unblocking of target path: %1 failed. Error Code: %2
Warning—If you need to unblock your target paths, contact technical support.
4306 Target paths for source %1 (%2) Connection id: %3 are already blocked
Warning—No action required.
4307 Target paths for source %1 (%2) Connection id: %3 are already unblocked
Warning—No action required.
4308 Error loading target paths for blocking, registry key %1 has been corrupted.
Error—If you need to block your target paths, contact technical support.
5000 Server Monitor service was successfully started.
Information—No action required.
5001 Server Monitor service was successfully stopped.
Information—No action required.
5002 Placeholders were modified to %1.
Information—No action required.
5100 Failover completed for %1.
Information—No action required.
5101 IP address %1 with subnet mask %2 was added to target machine's %3 adapter.
Information—No action required.
5102 %1 has reached a failover condition. A response from the user is required before failover can take place.
Warning—User intervention has been configured. Open the Failover Control Center and accept or decline the failover prompt.
5103 Started adding drive shares from %1 to %2.
Information—No action required.
5104 %1 drive shares were taken over by %2.
Information—No action required.
5105 Attempting to run the %1 script.
Information—No action required.
5106 The %1 script ran successfully.
Information—No action required.
5107 Error occurred in running %1 script.
Error—Verify that the script identified exists with the proper permissions.
5108 The source machine %1 is not responding to a ping.
Error—This occurs when all monitored IP addresses on the source machine stop responding to pings. Countdown to failover will begin at the first occurrence and will continue until the source machine responds or until failover occurs.
5109 The public NIC on source machine %1 is not responding to a ping.
Error—The failover target did not receive an answer to its ping of the source machine. Eventually, a failover will result. Investigate possible errors (down server, network error, etc.).
5200 Failback completed for %1.
Information—No action required.
5201 IP address %1 was removed from target machine's %2 adapter.
Information—No action required.
5202 Unable to Failback properly because IP address %1 was missing a corresponding SubNet Mask.
Error—Contact technical support.
5300 The following IP address was added to target's monitoring list: %1
Information—No action required.
5301 The following IP address was removed from target's monitoring list: %1
Information—No action required.
5302 Drive share information for %1 has been updated on the target machine.
Information—No action required.
5400 Broadcasted new MAC address %1 for IP address %2.
Information—No action required.
5500 Could not connect to e-mail server. Check to make sure the SMTP server %1 is available (error code: %2).
Warning—Double-Take Availability could not connect to your SMTP server or the username and/or password supplied is incorrect. Verify that SMTP server is available and that you have identified it correctly in your e-mail notification configuration. Also verify that your username and password have been entered correctly.
5501 E-mail notification could not be enabled (error code: %1).
Warning—This alert occurs if there is an unexpected error enabling e-mail notification during service startup. Check to see if any other errors related to e-mail notification have been logged. Also, check to make sure the Windows Management Instrumentation (WMI) service is enabled. If neither of these apply, contact technical support.
5502 E-mail notification could not be initialized. Check to make sure Internet Explorer 5.0 or later is installed.
Warning—E-mail notification no longer requires Internet Explorer 5.0 or later. If you receive this error, contact technical support.
5503 E-mail notification could not be processed. Check to make sure the correct version of SMTPMail.DLL is registered on the system (error code: %1).
Warning—If you are using Double-Take Availability 4.4.2.1 or earlier and Windows NT 4.0, e-mail notification requires Windows Management Instrumentation (WMI) to be installed. Verify that you have it installed on the Double-Take Availability server.
5504 Could not load LocalRS.dll (for e-mail notification).
Warning—This alert occurs if there is an error loading the resource DLL for the service. Typically, this is caused by a missing LocalRS.dll file. Reinstall the software, using the installation Repair option, to install a new copy of the LocalRS.dll. Contact technical support if this error persists.
5505 E-mail could not be sent. Check e-mail settings (error code: %1).
Warning—Verify that the e-mail server that you have identified in your e-mail notification configuration is correct.
5506 One or more required e-mail settings have not been specified (error code: %1).
Warning—At a minimum, you must specify the e-mail server, the From and To addresses, and at least one type of event to include.
5507 E-mail notification could not be initialized. Check to make sure WMI is installed and available (error code: %1).
Warning—If you are using Double-Take Availability 4.4.2.1 or earlier and Windows NT 4.0, e-mail notification requires Windows Management Instrumentation (WMI) to be installed. Verify that you have it installed on the Double-Take Availability server.
5508 An error occurred connecting to the WMI namespace. Check to make sure the Windows Management Instrumentation service is not disabled (error code %1).
Warning—This alert occurs if there is an error with the Windows Management Instrumentation (WMI) service. Verify that you have it installed on the Double-Take Availability server and that it is enabled.
5600 Part or all of the e-mail setting %1 is not in a valid format.
Warning—Verify that the include categories and exclude ID list are identified and formatted correctly.
Related Topics